Connect the computer and the router by plugging the cable into network card computer and LANport router.

1. Check the network connection settings on the computer.

Windows XP (Control Panel-Network and Internet-Network Connections-Local Area Connection.)

Windows 7 / 8 (Control Panel - Network and Internet - Network and Sharing Center - Change adapter settings - Local Area Connection)

Right click on LAN connection - select " properties". Double click on " Internet protocol version 4". Set the switches to automatic receiptIP addresses.

2. We launch any Internet browser (Internet Explorer, Opera, Google Chrome and others). In the address bar of the browser, write the IP address of the router - 192.168.0.1 and press the key Enter(for the initial configuration of the router, Internet access is not needed).

3. Login to the router.

3.1. If the router is being configured for the first time, then the first time you log in, it will ask you to set a login password. Standard login/password pair: admin/admin

3.2. If the router has already been configured before, then enter your login and password to enter. Default loginadmin, passwordadmin.

4. Remove existing connections.

Go to " Net»-« WAN". Check the boxes next to the created connections and click on the " Delete»

5. After deleting, click on the " Add". Select the connection type from the dropdown menu. PPPoE».


6. In the window that opens, in the section ethernet, you must specify the MAC of your computer, otherwise you will have to contact technical support to unbind by MAC address.

Fill in the fields Username And password. The data is provided in the contract. MTU should be equal 1492 . We press the button Apply.

7. Connect the internet cable to WANport router. The connection will change to the "Connected" status.

8. For the correct operation of the IP-TV service, both via cable and Wi-Fi, you need to add one more connection - Static IP. Press the button again Add.

Connection type - Static IP



9. In the window that opens, fill in the windows and click the " Apply».

IP-address: 192.168.1.10

Netmask: 255.255.255.0

IP- gateway address: 192.168.1.9

PrimaryDNS- server: 188.168.69.69

SecondaryDNS- server: 188.168.81.2

Check the box " Turn onIGMP»

After applying the two connections should be in the status " connected". Default gateway PPPoE

10. To customize Wi- fi. Go to the section " Wi- fi»-« basic settings". In the window SSID you can customize the name of your point. Click " Apply».

To set a password for accessing a Wi-Fi point, go to the " Wi- fi»-« Security Settings". On the menu " network authentication» select « WPA- PSK/ WPA2- PSK mixed". Enter the password in the window " encryption keyPSK» . Click the button Apply.

11. Save your changes to complete the settings. At the top of the screen, click on the inscription " Save».


12. In order to find your network, you must click on the icon Net located next to the clock in the lower right corner and select your Wi-Fi network. Click on it with the left mouse button, then Connection, and enter the network password.

First of all, consider the general scheme for connecting the router.

As you can see, everything is quite simple, connect a computer / laptop to any LAN port (there are 4 of them) using a network cable (it is included), insert the provider's network cable into the WAN port, connect the router to a 220V network and press the Power button.

Now I propose to disassemble the indication of the router.

Indicator - Power
Does not burn- Dlink dir300 is off.
Lit- Meals included.

Indicator - WPS
Flashing slowly - Attempting to establish a Wi-Fi connection using the WPS function
Does not burn- The WPS function is not used.

Indicator - Internet

Lit- Connection established
Flashing- WAN interface active
Does not burn- The network cable is not connected.

Indicator - Wireless network Wi-Fi
Does not burn- The Wi-Fi network is off.

Flashing- Wi-Fi data transfer in progress

LAN ports 1-4 Connecting to Network Connectors
Does not burn- The cable is not connected to the corresponding socket of the Keenetic, or the network connection is not established.
Lit or flashing The network connection is established and information is being transferred.

Next, I propose to proceed to setting up the router, for this, on a computer / laptop, you need to configureautomatic retrieval of network settings . After that, open any browser (IE, Chrome, Yandex, Firefox, Opera) in the address bar, write the IP address of the router 192.168.0.1 . If you are connecting to the web interface for the first time, you will be prompted to change your login password. I recommend using a complex password - at least 8 characters using letters, numbers and specials. signs.

If you have already connected, enter the login - admin and the password - the one you specified (admin is used by default). If the web interface uses a language that does not triple you, click the "" button in the upper right corner language", and select the desired language.

To save the settings, click the " Save". In the future, also do not forget to press the button" Save".

Firmware update on Dlink dir 300 D1 router.

For a more stable and secure operation of the router, the first thing to do is to update the firmware of the router, for this, look at what version of the firmware you have installed, this information is in the main window of the web interface.

Then find out the hardware revision (H/W) of your router. To do this, look at the glued label, which is located at the bottom of the router. This sticker has an inscription that begins with "H/W Ver.:". Followed by a letter and a number indicates the hardware revision (in this example Dlink dir- 300 D1).

Then download the latest firmware version according to your revision.

Important!!! DO NOT install firmware of hardware revisions other than yours, this can lead to a complete failure of your device. After that, it will be possible to restore the router only for money by contacting a specialized service center.

After that, on the web interface of the router, click on the version of the installed firmware.

Click " Review"specify the path where you have the firmware file (file with extension.bin). Then press the button " Refresh".

Attention!!! During the firmware update, do not turn off the computer / laptop, router. This can damage the router and disable it.

The firmware update will take about 2-3 minutes, during the update the router will reboot. After the router boots up, you will see the updated firmware version.

Internet setup on Dlink dir-300.

To configure the Internet and Wi-Fi, you need to go to the web interface of the router in the menu "Net" press the button "Click'n Connect".

Then make sure you have inserted the ISP cable into the WAN port and click " Further".

After that, you must specify the type of connection to the Internet, you can find this information from the provider's contract or contact those. provider support.

Confirm the specified settings.

If the setup is successful, you will see a window confirming Internet access. Don't forget to click the " Save".

Setting up a Wi-Fi network on Dlink dir-300 D1

If you need DIR-300 firmware, then here you will find all the information you need. It is worth noting a few points:

  • If during flashing your electricity goes out, then there is a chance to break the router. Therefore, first make sure that the electricity is stable and the power cables are working. You can connect D-link DIR 300 through the UPS for the duration of the firmware.
  • Self-updating the firmware will void the warranty.

    • Why might an update be required? Sometimes you don’t even need an update, but a reinstallation of an existing firmware version. Causes:

    • The internet is slow and buggy.
    • Requires new features that have appeared in the new version of the software.

    Firmware is like a driver or operating system for a router. Firmware written to the device's read-only memory. To get started, you need to download it.

    Brief instruction

    In short, the very essence of how to reflash:

    • Download firmware for D-link DIR 300 from ftp.dlink.ru.
    • Go to the router page 192.168.1.1 (or 192.168.0.1).
    • Head to the "Maintenance" section, then "Firmware Update".
    • Select the firmware file, click "Upload".
    • Wait 2 minutes while the router installs the firmware. All.

    Now everything is the same, but more detailed.

    firmware download

    • It weighs only a few megabytes. In the address bar, write the address dlink.ru, then go to the official website of the router developer, this is ftp with firmware.
    • In the folder called pub, find the Router section.

    • After that, find the folder with the firmware for your model and revision of the router, in our example it is DIR-300_NRU.

    • Next, head to the Firmware folder.


    • Now you need to find out the revision of the DIR router. You need to take your router, turn it over, and see what is written on the sticker on the bottom side.
    • In this case it's B1, you could have A1/B1/C1/D1/B3/B5/B7/B6.

    • After opening the ftp folder called Firmware, select the section that matches your DIR300 router model.

    • Download firmware. This is a small file with a bin extension.

    Connecting the Router to a PC

    Connect D-link to your computer via patch cord. You can reflash from ordinary stationary PCs, laptops and netbooks. Turn on the router. You need to check your network settings.

    • In Win7, go to "Start", then to "Control Panel", then "View Network Status and Tasks".
    • Find the link "Change adapter settings" in the left menu. Find the icon for connecting by lok. network, go to connection properties.
    • A window will open, select protocol version 4 (TCP/IPv4) there and click the "Properties" button.

    • On the “General” tab, check if the settings are set: “Obtain an IP address automatically”, as well as “Obtain DNS server address automatically”.

    Now directly to the firmware update.

    flashing


    • Open the browser, write 192.168.1.1 instead of the site address, you will go to the page generated by the router.
    • Enter your login and password to access the DIR 300 settings. If you did not set a password, then simply write admin.
    • On the router page, you can find out the revision version (marked with a light green arrow at the top), this is necessary in case you have a sticker on the bottom of the router that has become stuck or peeled off.
    • Go to the "Maintenance" section, then to "Firmware Update. Then scroll down to "Firmware upgrade" then "Select file".
    • Find on your computer the downloaded official firmware from D-link. After that click "Upload".

    • The firmware update of the router will begin, it will take exactly 2 minutes. Do not unplug the router during this time, otherwise it may cause damage.


    • When the update is over, you will be transferred to the login and password window.
    • Look at the top line, if you updated the firmware to a new version, then there should be changes. If you just reflashed (by analogy, like reinstalling Windows), then the same firmware version number will be waiting for you.

    When the firmware of the DIR-300 router is reinstalled, the Internet settings do not change. You can immediately continue using your computer.

    Firmware for D-Link DIR-300 C1


    • To reflash the D-Link DIR-300 C1 router, you need to download the firmware file (.bin) from here.


    • Then download the zip archive from here.


    • Make sure your router is connected to your computer (laptop or netbook) with a cable connection and not via Wi-Fi.
    • Unpack the downloaded zip archive on your computer and run the dcc.exe program.
    • This will launch D-Link Click'n'Connect. In it, select "Connect and configure the device."

    Update the software, it's easy - tips will help. As a result, not the latest, but working firmware for this model will be installed. If the operation of the router suits you, then you can not continue.

    Update D-Link DIR-300 C1 to the latest version

    But if you want to update the D-Link DIR-300 C1 software to the latest firmware, then…

    • Go to the router settings, find the "System" section, then "Software Update".
    • There, select the firmware bin file (we downloaded it earlier).
    • Then click "Update" - wait for the standard 2 minutes for the update.

    Error messages or router freezes may appear, then do not turn off the power, but wait another 5-10 minutes for the installation to complete correctly.

    DIR 300 N150 revision D1

    Flashing DIR 300 N150 D1 on the example of firmware version 2.5.4 with a new web interface "Air".


    • Go to the settings in the usual way, you will see the "Start / Information" page in front of you, there you can find the exact model name and firmware version.

    • To install a new or reinstall an old firmware, click on its version, the "System / Software Update" page will open.
    • Use the "Browse" button to select the update file (previously downloaded from here).
    • Click "Update". Waiting 2 minutes.


    This is how the firmware file looks like on the manufacturer's ftp server

    Restore settings

    If you flashed the DIR-300 unsuccessfully, you can restore the factory settings of the router.

    • The simplest is to use the RESET button on the router case, you will need a toothpick, since the button is recessed into the case. Press it for 10 seconds, release, after that the router will reboot and start with reset settings.
    • You can also use the corresponding item in the web interface settings menu.

    You have learned how to install the official firmware on the DIR 300 router (revision A1/B1/C1/D1/B3/B5/B7/B6). Also on our website you can read how to set up the Internet on a D-link DIR 300 router.


In this article, we will only talk about the dir300 router, revision B1. Turn the router over and look at the bottom surface, where its hardware revision will be indicated on the sticker (we are looking for the line H / W Ver: B1). This model differs from the older one both in appearance and firmware version (starts from 2.00), take a close look at the photo above. The main difference between revisions A1 and B1 is the chip on which the router is based, in our case, the H / W Revision B1 router is based on the Ralink RT3050 chip. By the way, the hardware version of the dir-300NRU WiFi router is exactly the same as that of the dir-600, which is a complete analogue of the 300NRU and is produced for the European zone.

Firmware for WiFi router D-Link DIR-300NRU Rev. B1

Installing the DD-WRT firmware on the D-Link DIR-300 Revision B1 is performed through the standard web interface of the router. Further points:

1. Download the firmware from this site or check for a newer version at http://dd-wrt.com/site/support/router-database by searching DIR-300 B1. We need the file exactly dlink-revb- factory-webflash.bin

2. We connect dir-300 with a 'straight' network cable from the kit (any of the 4 LAN ports of the router) with the computer.
Assign the IP address 192.168.0.15 and the subnet mask 255.255.0.0 in the properties of the LAN connection on the computer

3. Launch a browser (it is best to use IE) and go to the web interface by typing http://192.168.0.1 in the address bar
We enter the login and password, for the new router the default login is admin, there is no password (empty) and the confirmation code from the picture. If you set it up, please enter your passwords.
Go to the Maintenance tab and then Firmware Update, click "browse" -> look for the downloaded file dlink-revb-factory-webflash.bin, click "Upload"

4. For several minutes, while the DIR300 is being flashed, you must not turn off the power and interrupt the process in every possible way. For reliability and to save a certain amount of nerves, I advise you to do this operation by connecting the router and computer via UPS (uninterruptible).

5. After flashing, the router will go into reboot and become available at 192.168.1.1. Let's enter it into the address bar of the browser and we will see the DD-WRT web interface. If the page does not load, try clearing the browser cache, close and reopen. The login and password of the DD-WRT firmware is root/admin.

DD-WRT version update

For subsequent firmware updates from DD-WRT, you should use the file dir300-revb- ddwrt-webflash.bin. Download here - or on http://dd-wrt.com/site/support/router-database by typing DIR-300 B1 into the search.

1. Open the DD-WRT web interface in the browser, by default it is located at 192.168.1.1
2. Select the Administration tab -> click "Firmware Upgrade"
3. Next, “browse” -> select the downloaded file “dir300-revb-ddwrt-webflash.bin” -> “Upgrade”

After a few minutes, the router will reboot and update the web page. I recommend that after the firmware, turn off the power to the router and turn it on again (a kind of power reset).

Return to the official D-Link firmware

Returning the official firmware is also not difficult and the execution algorithm is exactly the same as in the paragraph - “Updating the DD-WRT version”. Naturally, we need to have a pre-prepared firmware file, download - . You can also download from the official D-link FTP server ftp://ftp.dlink.ru/pub/Router/DIR-300_NRU/Firmware/ by selecting the latest version.

Rollback to factory firmware using Emergency Room

Sometimes there are situations when it is impossible to return to the factory firmware using the method described above. In this case, we use the Emergency Room.

1. We reset to factory reset, either through the DD-WRT web interface, or with the reset button.
2. We remove all ethernet cables, leaving only the LAN1 connection of the router -> PC. We always use a "straight" wire (blue from the kit).
3. In the properties for the network adapter of the computer, we prescribe the static address 192.168.0.15, the subnet mask 255.255.0.0
4. We take out the power supply plug from the router, press the reset button, and without releasing the button, insert the power back, wait for the router to boot for about 15 seconds and only then release the button.
5. Now quickly open the browser, enter http://192.168.0.1 and we have the Emergency room. Select the firmware file dir300b_v2.05_abnj.bin and click "Upload Now".

Well, now briefly, what is this idea with flashing DIR 300NRU for.

The firmware is based on Linux and is a miniature operating system, there are many advanced settings that are much more logically arranged. The ability to cut the channel with priorities for services (QoS). You can block sites by page address or simply by domain name.

D1 is very similar to the process with other devices, but some people still have a lot of questions.

These issues are mainly related to downloading the “D-Link DIR-300 NRU firmware” file from a website created by D-Link, as well as issues related to the updated interface in the firmware, which is clearly seen in the example of version 2.5.n

In this description, we will consider how to reflash the D-Link DIR-300 router by receiving the latest version 2.5.n firmware for the DIR-300 D1 model from the site and how to perform the installation correctly, provided that the firmware with additions and updates was installed in the router at the factory 1.0.4. In this guide, I will try to take into account all the nuances that arise during installation.

d link dir 300 router firmware: stage 1

The explanation of how to flash the DIR-300 is only suitable for routers that have the following letters on the bottom of the case: H / W: D1. If the values ​​are different, then you need to download a file with a different firmware.

Where to download firmware d link dir 300

  • We go to the manufacturer's Internet project, which is located at http://ftp.dlink.ru in order to download the file itself.
  • On it, go to the pub folder, then to a folder called Router, and then to DIR-300 (underscore) NRU and find the Firmware folder in it. It should be noted that inside the Router directory there are DIR-300 A D1 directories. Their differences are that in one of them there is an underscore, and in the other there is no such symbol, written in one word. To update the firmware of the D-Link DIR-300 router, you need the file that I specified.

This directory contains the firmware itself.

All of them have the end of the name.bin

When this article was written, the latest firmware file was created in 2013. I will install this version in this one created in 2013. I will install this version in this guide.

Preparation before installation

If you know how to get to the settings section of the connected device, then in such a case you can skip this section. The only thing I would like to note is that updating the firmware of the D-Link DIR-300 router and the main changes are best done using a modem connection using an Ethernet cable.

If the router is disabled and the user has not performed the previously described actions:

  1. The router must be connected using a wire (supplied with the device) to a personal PC, using which the firmware will be performed. It should be noted that on a personal PC, the input for the network card is the LAN1 port on the device. If your mobile PC does not have such a port, you will have to skip this step. The connection is via Wi-Fi.
  2. Connect the device to a power outlet. When using a Wi-Fi connection, after one or two minutes, a network called DIR-300 will appear, which will not be password protected, provided that the name and other parameters have not been changed. You need to connect to the network that appears.
  3. We open the browser and prescribe where you usually write the URL of the desired site: 192.168.10.1. If the page does not open, you need to open the TCP / IP protocol settings and check the box next to the inscription Obtain an IP and DNS address automatically.
  4. When a form opens in which you need to register a username and password, you must enter admin. The first time you will be asked to change your password. If you do not change it, you must not forget the new password, as it will come in handy for subsequent entries into the device settings. If the password does not work, maybe you, or someone else changed it before you, you need to reset all device settings. To do this, press and hold for a while the button called Reset, which is located on the back of the router.
  5. If the above was done correctly, what we were striving for began: flashing the D-Link DIR-300 router.

D link dir 300 firmware update using rev. B6

You will be shown the only one of the options you need, it depends on the version that is installed on the router. This is the settings interface.

In case number 1, if DIR-300 NRU rev. B6 version 1.n.n, you need to follow these steps.

  • We press the item "advanced settings", if the Russian language is not displayed, it can be changed in the Language section.
In the item "system", click on the arrow pointing to the right
  • Next on the software update.
  • Now we specify the firmware file, which we recently uploaded.
  • Click on the button called "update".

After completing all these steps, the waiting for the end of the process comes. And now, the D-Link DIR-300 NRU firmware is over. If suddenly you see that the installation process has stopped, or the page has stopped, you need to go to the "notes" section, which is located a little lower.

Router d link dir 300: beeline firmware

This paragraph is for users who need DIR-300 NRU firmware upgrade 2.n.n. In addition, this instruction is suitable if you need to install firmware on a router from Beeline.

  1. Go to the settings section
  2. A menu will open, where we select "System", then the updated software. If necessary, switch to Russian.
  3. Go to the "local update" section and click on the "Browse" button. Next, we indicate where the * .bin file lies in the file system of your personal PC.
  4. Click to update.

WATCH VIDEO

Note

If it suddenly seemed to you that while the update was in progress, or when the DIR-300 firmware was being installed, the router hung up. It seems similar if you notice that in the display window of the browser page where the update is taking place, a special installation bar is constantly moving.

It appears that the page is not loading. This may happen because the connection between the personal PC and the router has stopped during the software update. It is worth waiting two or three minutes, and then reconnecting to the device.

When using a wired connection, recovery will happen by itself.

Then you should go back to the settings and see that the update has happened.

Further, the necessary device settings do not differ in any way from the settings of the same models, but with other interface options. Differences in the design of the interface are not terrible. Now you know how to get the D-Link DIR-300 firmware and flash the device. Do you have any questions? We write them at the bottom of the article!