Errors when setting up the Sagemcom F@st 2804 router

Theoretically, setting up the Sagemcom F@st 2804, v7 router from Rostelecom is not a problem. Immediately after receiving the router for rent (a couple of years ago), I connected the device to the computer, inserted the supplied disk with the software (Settings Wizard program) into the drive, and after a few minutes the Internet was already working. A couple of days ago I needed to configure the same router for a different subscriber, but the setup from the disk ended with the red light coming on. Those. The Internet LED indicator (with the @ symbol - dog) signaled that there was no Internet connection.

The red light with the @ icon is on on the router - the Internet is unavailable

As a rule, this indicates that incorrect settings have been entered. Since the setup was carried out from the disk, I could only make a mistake when entering the login and password, but the catch is that they were previously “hammered” into Notepad and I simply copied and pasted them, i.e. the error has been eliminated. I reset the settings to factory settings several times and tried to configure the router again using the included disk, the result did not change.

As a reference, I remind you that you can reset the router to factory settings using the Reset button. To get to it, use a paper clip or toothpick.

Error messages during setup

During the “dancing with a tambourine” various errors occurred, which are presented below in the screenshots.

“The wizard did not detect the router” - this means that the setup program does not “see” the router at all

“The router is unavailable” - the message appeared during the Wi-Fi setup stage. Simply put, the computer “lost” the router again

I tried to go into the settings via the web interface (IP 192.168.1.1 , login and password admin), but I couldn't do it. I noticed that you can log in via the web interface without problems if the settings are reset to factory settings. I read on the Internet that the LAN cable should be connected to the second connector and use the IE (Internet Explorer) browser. Alas, the trick also failed.

It is not possible to reach the router’s web interface, although the IP address is entered correctly - 192.168.1.1

Where did the dog rummage?

After unsuccessfully trying to turn the red dog into a green one, I erroneously concluded that the router had failed. I contacted Rostelecom technical support (toll-free technical support number 8 800 100 08 00) and left a request. The next morning I waited for the call and found out key information - When setting up the router, the network cable must be connected to port No. 3, and not No. 2, as indicated in the online source.

When setting up the router, the network cable must be connected to the LAN3 connector - on the Sagemcom 2804 router in a white case, it is marked in green

After connecting the cable to the correct connector, I was able to go into the Sagemcom F@st 2804 settings via the web interface and understand the reason why the “dog” icon was red after trying to configure from the disk. It turned out that the information about the login and password was not saved from the disk after configuration - the corresponding fields were empty!

After entering the username and password, the Internet started working.

The “dog” icon turned green - the Internet is working! Pay attention to the icon for connecting to the Ethernet port - the number “3” lights up next to it, indicating that the cable is connected to LAN3

Is it really that simple?

As my further excrements showed, configuration using the Settings Wizard may end with errors even if the network cable is connected to the LAN3 connector.

As I understand it, the errors “Presence of PPPoE connection” and “Connection to Rostelecom server” indicate that the login/password pair was entered incorrectly, although I again copied the data from Notepad. As you probably already guessed, the login and password were again not saved in the router settings.

There are two ways to solve the problem:

  1. Go to settings via the web interface and add a login and password;
  2. Restart the router setup from the disk.

Was it possible to do without unnecessary headaches?

It often happens that we pick up the instructions only after we have broken something :) If you take the paper instructions for the Sagemcom F@st 2804, v7 router, then it does not say anything about the need to connect a network cable to the LAN3 connector. However, this is clearly indicated when using the Setup Wizard, which is installed from the CD.

To be honest, I didn’t pay attention to this nuance at all, perhaps due to the fact that earlier, for which the port number is not critical. In general, I wonder how the LAN3 port on the Sagemcom 2804 differs from others?

conclusions

  1. When setting up the Sagemcom F@st 2804, v7 universal router from Rostelecom, connect the network cable to the LAN3 port (marked in green).
  2. To avoid the hassle of setting up your router via the web interface, use the Settings Wizard from the included CD. If you don’t have a CD, download the Settings Wizard from the official Sagemcom website (the clever software is called “Automatic configuration and firmware update/recovery program”, in short, a settings program).
  3. Sometimes you should read the instructions - in many cases this will save you unnecessary headaches.
  4. Learn from the mistakes of others, and specifically from ours. To do this, do not forget to bookmark the site :)

In the vastness of our market, a universal and inexpensive device has been spotted - the multifunctional ADSL router F st 2804 v7. In the version provided by Rostelecom, everything is perfectly configured from the included CD. But MTS today provides a similar device with an even greater range of capabilities, but it must be configured via a web interface. In general, the MTC Fast 2804 router creates an ADSL connection no worse than devices from Rostelecom. How to set it up is discussed below.

Routers Fast 2804

In fact, all devices with the word “Fast 2804” in their name are produced by one company – Sagem (also known as Sagemcom). Routers of versions v3, v5 and v7 have reached our country. They may differ in the shape of the case, in addition, the graphical interface is made for a specific provider. In general, these routers have the same capabilities. In terms of setup, the “from MTS” option is the most complicated, although it can create an ADSL connection. We are trying to configure this router for a connection under the PPPoE protocol, in case the connection is provided by a telephone wire. Let's get started.

Setting up basic functions

Connecting the router before setting up

We will configure the MTS device like any other “home” router. First, we connect any LAN port to the PC network card with the supplied patch cord:

Connecting the router to a PC

Then, connect a telephone cable to the ADSL port (you can use the splitter included in the kit). At the final stage, power is supplied to the router (but first, you need to configure the network card in the PC):

Setting up a wired connection on your computer

This completes the preparatory steps. After turning on the router, you need to wait 2-3 minutes, after which you can log into the graphical interface from your computer.

Authorization in the graphical interface

On your computer you need to open any browser (at least IE5) and go to the address: 192.168.1.1.

If everything is done correctly, an authorization window will appear. “admin” is suitable as a login (and “mts” as a password). If authorization is passed, the user will see the following tab:

Main tab of the web interface

The graphical web interface is divided into tabs, which are combined into two lists: “Basic settings”, “Advanced settings”. The first list, as you can see, contains 5 different tabs. Now we will look at how to set up an ADSL connection.

Setting up a connection (PPPoE option)

The F st 2804 router can connect to the Internet via a telephone wire or a 3G modem. We will look at the simplest setup option, when the built-in ADSL modem is used to create a connection, and the provider’s protocol is called “PPPoE”.

Before setting it up, it’s better to write it down on a separate piece of paper:

  1. Subscriber name and password (found in the contract);
  2. VPI and VCI parameter values ​​used by this provider (for example, 0 and 30);
  3. PPPoE encapsulation type: LLC or VC-Mux;
  4. For a permanent IP address (a separate service, usually provided for a fee), you need to know the value of the address.

Settings are made on the advanced mode tabs. Go to this list of tabs, turn on English. On the “Wan Service” tab, located in the “Advanced Setup” menu, you will need to remove (using “Remove”) all existing interfaces:

WAN interface tab with “old” values

ATM interface tab

The same must be done here. Then, you need to go to the “Wan Service” tab again. And now click the “Add” button:

A tab will appear to configure a new connection, where you can select a value, as in the figure:

Settings tab

Then, you need to click “Next”. On the next tab, you need to set the VPI and VCI values ​​(instead of the numbers 1 and 91):

For example, if the values ​​0 and 30 are true, the string would be "pppoe_0_0_30_3". Do not leave the values ​​as is - they do not correspond to the user's provider.

In addition, the connection protocol is selected here (after selecting PPPoE, a list will appear where you need to select LLC or VC-Mux). After completing the settings, you can click “Next”.

Connection settings tab

On the next tab, set the user name and password. For a dynamic IP address, you don't need to change anything else. “IGMP Proxy” can be enabled if you plan to watch IPTV. But for a constant IP value, you need to check the “Use static IPv4” checkbox and fill in the field that appears.

After completing the settings, you need to click “Next”, and “Next” again. A tab will appear where you can leave the automatic mode for obtaining DNS (or set certain address values). And the final tab looks like this:

Final connection settings tab

By clicking “Apply/Save” we get a new working connection.

Device Information Tab

The presence of a connection can be judged by the state of the main tab. Happy setup!

Enabling the wireless network

We will configure the Wi-Fi network using “additional settings”. The “Basic” tab from the “Wireless” menu allows you to configure everything you need:

Setting up a wireless network

Let us explain the meanings of the parameters. “Enable Wireless” turns on the transmitter, and “Hide Access Point” will allow you to work with a hidden name.

The SSID field contains the network name (set as required). It is better to set the Country to “RU”. After completing the settings, click the “Apply/Save” button. Wireless network will appear automatically.

Note that the universal router F st 2804 has serious capabilities. For example, the device independently selects the least noisy channel (in the 2.4 GHz range). Automatic selection mode – can be disabled. The transmitter power can also be adjusted. All these parameters are located on the “Advanced” tab, but the user is not recommended to change them unless properly qualified.

The “Security” tab contains encryption options. We do not consider setting up network security.

Additional router features

Setting up IPTV

Oddly enough, the Fast 2804 router creates Internet connections that are several times faster than 3-4 Mbit/s. Therefore, you can view IPTV through computers connected to the local network. To enable this option, you must:

  • When setting up a connection, check the “Multicast Proxy” box (discussed above);
  • On the local network settings tab (“Advanced Setup” -> “LAN” among the “additional settings” of the router), you need to check the “IGMP Snooping” checkbox:

LAN settings tab

After completing these settings, you can watch TV through any computer connected to the router’s network. Now multicast packets used in IPTV enter the local network from the Internet.

Additionally, it is possible to limit multicast traffic on the wireless network. To do this, you need to go to the “Wireless” -> “Advanced” tab (also located in the “advanced settings”) to set the required value in the “Multicast Rate” list. An acceptable choice is 9, 11 or 12 Mbit/s, which is enough for FullHD viewing.

Question answer

Question: I can’t access the graphical interface. IP address 192.168.1.1 is not available.

You can try resetting the router to factory settings. To do this, after turning it on, you need to wait 2 minutes, then press the “RST” button on the rear panel (holding it for 15-30 seconds).

Question: what is the speed of wireless connections, was it not said about choosing a mode (N/G/B)?

This router operates in “mixed” B/G/N mode, the maximum transmission speed in the wireless network is 65 Mbit/s. The use of the “N Only” mode (N only) is not provided.

How to remove the router from the package and connect it correctly is shown in the video:

The universal router F@st2804, v7 rev.1 is compatible with the 802.11b/g/n WFA specification and allows connection speeds of up to 300 Mbit/s. 2 USB 2.0 ports, work with 3G USB modem

Sagemcom F@st 2804, v7 rev.1 can work both via xDSL technology and via UTP cable. Those. WAN ports are available for both types of connection technologies. This fact should be taken into account when setting up the connection. We will reflect this in the Internet connection settings item. I would also like to note that Sagemcom F@st 2804, v7 rev.1 can only be configured for a PPPoE connection or in bridge mode.

Instructions for setting up the Sagemcom F@st 2804 v7 rev.1 and Sagemcom F@st 2804 v7 rev.1B router

Authorization

In order to get to the router’s web interface, you need to open your Internet browser and type 192. 168.1.1 in the address bar, Username - admin , Password - admin(provided that the router has factory settings and its IP has not changed).

Features of setting up a modem + wi-fi router

1. This modem has an IP address of 192.168.1.1. Therefore, if you connect to Sagemcom 2804 router Asus, NetGear, Tp-Link or ZyXEL(these router models have the same IP address - 192.168.1.1) - do not forget to change the address of one of the devices to something else, for example 192.168.0.1

2. There are two settings options:

  • modem Sagemcom 2804 configures it in router mode (PPPoE Internet connection is created on the modem), and on the router select Static IP (Static IP) or Dinamic IP (DHCP or Dynamic IP) mode;
  • modem Sagemcom 2804 configure it in bridge mode, and create an Internet connection (PPPoE) on the router;

3. If the subscriber has an IP-TV service, then on the modem Sagemcom 2804 DHCP will be disabled. Therefore, on the router you select the Static IP connection type and enter IP addresses manually.

Setting up Wi-Fi on the router

1. Find the menu item on the left WLAN setup;, in the window that opens, check that the parameter is checked Enable wireless connection; And Enable multicast transmission via wireless network (WMF);. SSID- name of the wireless connection, leave it as default or change it to your own, press the button Apply/Save;

2. Next, open the Security submenu, on the left and in the tab that opens disable the WPS option, check that authentication is selected WPA-PSK, encryption WPA - TKIP+AES. To protect the network with a key, either register your own or click the button opposite WPA/WAP To display, click here; and in the window that opens, rewrite the password. Click Apply/Save;

Setting up an Internet connection

Before you configure the router, you need to reset its settings to factory settings. To do this, go to Settings options;→ Reset;→ Restore default settings;.

The window below will appear in front of you. We wait 2 minutes.

After resetting the settings to default, you need to remove unnecessary add-ons from the router. Go to the tab. Next, check 3 checkboxes as shown in the screenshot below and click Delete;.

Next, go to the tab Additional settings;→ Level 2 interface;. Next, check the single box as shown in the screenshot below and click Delete;.

Internet setup via xDSL

Additional settings;, Level 2 interface;. Press the button Add; in the middle of the window.

We follow the setup wizard; we correct only 2 points VPI and VCI to the parameters that Rostelecom uses. Click Apply/Save;

We check that the appropriate layer 2 interface is selected (in our example it is 0_0_35) and click Further;

In the WAN service configuration, we decide how the modem (router, bridge) will be configured and click Further;(see example of configuration by router)

In the window that appears, enter PPP username;- login, PPP password;- password. PPPoE service name;- any. Put a tick in the box PPP retry on authentication failure; And Enable IGMP Multicast Proxy;, Further;

In the next two wizard windows; We check that the created interfaces are in the left column. If they are on the right, move them to the left and press Further;

Internet setup via ETTH

Go to the tab Additional settings;→ ETH interface;. If this is empty, add an entry. If it already exists, then do not change anything (by default, a WAN port is created for eth0 - the first LAN port).

Go to the tab Additional settings;→ WAN service;. Click Add;.

Choose eth0/et0 Further;.

Put a point on PPP over Ethernet (PPPoE), press Further;.

Enter in section Username; enter the subscriber's login, respectively, in Password;- subscriber's password, in PPPoE service name;- int. Click Further;.

Then left column Available routed WAN interfaces; select the item ppp1.1; and press the button <- . Click Further;. Similarly then in the left column Available WAN interfaces; select the item ppp1.1; and press the button <- . Click Further;.

Setting up IP-TV

Setting up IP-TV for different connection technologies is different.

Setting up IP-TV via xDSL

In the main window, click the menu item on the left Additional settings;, Level 2 interface;. In the table that appears, if there are already configured connections for IP-TV, delete them (we delete them first in the WAN service menu, then in the Layer 2 Interface). Then press the button Add; in the middle of the window.

We correct only 2 points VPI and VCI to the parameters that Rostelecom uses. Click Apply/Save; at the bottom of the window (the picture shows the Rostelecom Omsk setting)

We add another interface to the WAN service configuration, where we check that the appropriate layer 2 interface is selected (in our example it is 0_1_36) and click Further;

For the modem to work correctly with STB set-top boxes (IPTV), you need to go to the LAN parameter in the left menu and disable DHCP (Dynamic Host Configuration Protocol) in the window that appears. Then check that IGMP Snooping is enabled and click the button below Apply/Save;

Let's go to Interface grouping and press Add;.

Create a group:

  • Group name; - any, for example IPTV;
  • We transfer the desired connection to the left column using special arrows;
  • Move the required LAN port to the left column. Just don’t forget that the serial number of the LAN port written on the device’s body is one digit greater than the one in the WEB interface. That is, if I want to connect the fourth port to television, then in the WEB interface I transfer eth3;

As you can see, we have two groups - one for IPTV, the second - with everything else (the remaining LAN ports and WiFi). But that's not all!

Go to the LAN tab; and in the Group Name field; choose ours, created for IPTV.

Put a tick on Enable IGMP Snooping; and press Apply/Save;.

Setting up IP-TV via ETTH

Go to the tab Additional settings;→ WAN service;. Click Add;.

Choose eth0/et0(or the interface you created above) and click Further;.

Put a point on Bridging, press Further;.

Port forwarding/forwarding

Select NAT ---> Virtual servers ---> Add

Use interface: select the interface that you created for the Internet (in our example this is xDSL)

Service name:- either choose from the list or create it yourself.

Server IP address: address of the device on the network to which the request will be redirected

External portInternal port: range of ports that need to be opened

The f@st 2804 v7 rev1 router is a universal network equipment necessary for connecting end devices to the Internet and IP-TV via an Ethernet cable, telephone line and wireless cellular communication via a 3G/LTE modem.

And this article discusses in detail the configuration of the Rostelecom fast 2804 v7 router, as well as its main characteristics and the configuration of a 3g modem.

By the way, the advantage of this router is that, at its relatively low cost, it supports almost all the functions necessary for the average user: from setting up a print server to the ability to reserve the main Internet channel.

Sagemcom f@st 2804 v7: characteristics

In addition to the standard capabilities of distributing Internet traffic and IP-TV between several functional nodes of the local network, the f@st 2804 router also supports additional functions such as:

  • - creation of a backup Internet channel (in case of a power outage or problems on the side of the main communication provider);
  • - the ability to use the router as a print server (to connect several user devices to a network printer);
  • - the ability to use f@st 2804 as a network drive (in other words, when you connect a hard drive to the router, it can be “used” as a miniature server).

On the front panel of Sadzhemkom fast 2804 there is a block of router indicators:

1. Power indicator. The normal operation of the modem is indicated by the constant green color of the Power indicator.

If this LED lights up red, then the fast 2804 modem is in emergency recovery mode, which starts when the router software is slightly damaged.

2. DSL indicator, which with a constant green light notifies the user about a normal ADSL connection, and with rapid blinking - about the establishment of this connection.

3. Internet indicator, which should glow solid green if the connection is successful through the Internet account.

4. WLAN indicator, which lights up green when the wifi module is activated on the router.

5. Several ETH indicators that light up when external devices are connected to the corresponding Ethernet port via a network cable.

6. WPS indicator, green color means successful connection with the user device via .

7. USB indicator indicating successful connection of external media to the sagemcom fst 2804 v7.

On the back of the fast 2804 v7 rev1 there are:

One ADSL port for connecting to the Internet via a telephone line;

4 LAN ports (for connecting to a router via twisted pair);

A small hole with a Reset button recessed into the case (to reset the router to factory settings, you need to press this button with a paper clip or a needle and hold it for 10 - 15 seconds);

Power connector (to which the sagemcom f st 2804 v7 power supply is connected);

Power button;

On the right side panel of Sajekom fast 2804 there are:

Connecting sagemcom f st 2804 v7

When connecting to the Internet via an ADSL telephone line, the cable provided by the provider should be connected to the splitter input (LINE), and a telephone set and router should be connected to its PHONE and MODEM outputs, respectively.

When connecting to the Internet using WAN Ethernet technology, the provider’s network cable must be connected to the first LAN connector of the Sadzhemkom 2804 router.

Modem Rostelecom f st 2804 v7: setup instructions

If the computer (on which the Rostelecom fast 2804 v7 router will be configured) is correctly connected to the router via twisted pair, then the following indication should be present on the router:

The first indicator lights up solid green;
- second indicator – slowly blinking green;
- fourth indicator – lights up or blinks green;
- one of the LAN ports – lights up or blinks green.

The setup of the Rostelecom fast 2804 v7 router described in this manual corresponds to the initial setup of the device. If the router has been in use before, it is recommended to first reset the device settings to factory settings using the Reset button.

Configuring the Sadzhemkom 2804 router using the Hardware Setup Wizard

To launch the fast 2804 router setup wizard, insert the disk supplied with the device into the computer's CD drive and follow the further instructions of the program.

Once the software installation is complete, the “Setup Wizard” will automatically launch (which can also be launched through the “Start” menu -> “Programs” -> “Hardware Setup Wizard”).

During the automatic configuration of the Rostelecom fast 2804 router, the following operations are performed:

  • - updating the router software from the installation disk;
  • - selecting the desired router configuration;
  • - configuration of PPPoE connection and 3G reservation;
  • - diagnostics of equipment performance;
  • - installing the latest version of the router firmware from the update server.

Manual configuration of the Rostelecom fast 2804 v7 router

In the absence of an installation disk, it is recommended to configure the Wi-Fi router f@st 2804 manually. To do this, in the address bar of any Internet browser installed on your computer, enter the combination of numbers 192.168.1.1 (the static IP address of the device indicated on the service label on the back of the sagemcom 2804) and press the “Enter” key.

It is recommended to subsequently change the default authentication data (login/password) to unique ones to protect your router from unauthorized access.

Initially, you will be taken to a page with basic technical information about the device.

Modem Rostelecom f@st 2804 v7: Ethernet connection instructions

1. To configure the fast 2804 v7 modem by Rostelecom, in the left vertical menu, select the “Advanced settings” section:

Here, first delete all connections created by default in the “Wan service” subsection;

In the “Layer 2 Interface” tab, remove “DSL ATM”;

Go to the “ETH interface” tab: select “eth0/eth0” from the drop-down list, set “VLAN/MUX Mode” in the connection mode and click the “Apply/Save” button.

2. When all unnecessary settings have been “cleaned up”, return to the “Wan service” tab, click the “Add” button and select the “eth0/eth0” port set in the previous step. Click "Next".

3. In the next window, select the service type “PPPoE” and write the value “-1” in the bottom two lines. Click "Next"

4. At the next stage, in the “PPP username” and “PPP password” windows, enter the username and password for connecting to the Internet from your agreement with the provider. Click "Next"

5. If the new window contains the columns “Enable NAT” and “Enable Firewall”, then place a marker next to each of them. In the subsequent windows (with the standard configuration of the Rostelecom fast 2804 v7 router), you do not need to change anything - click “Next” several times and at the end “Apply/Save” to make changes to the router settings.

How to configure a Rostelecom fast 2804 v7 router with an ADSL connection?

When connecting to the Internet via a telephone line, after deleting the standard settings in the first step of the previous instructions, go to “Advanced settings”, then “2nd level interface” and click the “Add” button.

  • - in the VPI and VCI columns, enter the data from the agreement with the provider (they can also be clarified in technical support) and click “Next”;
  • - go to “WAN service”, click “Add” and select an interface in accordance with the data entered in the previous window. Click Next.
  • - in “WAN Settings” select the “router” type and click “Next” again
  • - enter the login, password and PPPoE service name from the Internet connection agreement;
  • - set the marker to the fields “Retry PPP on authentication error” and “Enable IGMP Multicast Proxy”, then double-click “Next” and “Apply”.

sagemcom f st 2804 v7: wifi setup

Go to the menu section “WLAN Settings”;
- check the boxes “Enable wireless communication” and “Enable multicast transmission via wireless network (WMF)”;
- enter “SSID” (this is the name of your Wi-Fi access point) and click “Apply”;


- go to the “Security” section;
- if you wish, you can disable the WPS option;
- select the authentication type “WPA-PSK”;
- enter the Wi-Fi password;
- select WPA encryption “TKIP+AES”;
- click “Apply” to save the new settings.

Fast 2804 v7 router: setting up a 3g modem

Below is an approximate list of supported sagemcom fast 2804 v7 rev 1 3G USB modems
- HUAWEI: E220, E1550, E1552, E1752, E160G, E176G, E180, E169G, E150, HW601
- ZTE: MF112, MF626, MF627, MF180, MF190A
- Alcatel: X220, X080
- Airplus: MCD-650
- Withtel: WMU-100A
- Anydata: ADU-300
- Yota: LU156 (LTE)

To configure the 3g modem setup on the fast 2804 v7 router:

Connect the device to the special USB connector on the side panel of the router;

Go to the “3G Configuration” section of the web interface and set the marker to “Enable 3G reservation”;

With these settings, when the main (ADSL or Ethernet) Internet connection is disconnected, the router will automatically switch to the 3G/LTE channel.

Instructions for setting up the router: (Doc file)

To update the firmware, you need to go to the router menu:

Instructions for setting up the SagemCom 2804 router (WHITE) (“->” arrow means “click”).
First, open your browser and enter 192.168.1.1 -> “login” in the address bar.

1. RESET THE ROUTER SETTINGS.
1.1 -> “MANAGE” -> “SETTINGS” -> “RESET” -> “RESTORE DEFAULT SETTINGS”.
2.REMOVE STANDARD SETTINGS.
2.1 -> “ADDITIONAL SETTINGS” -> “WAN SERVICE” -> SELECT EVERYTHING IN THE TABLE WITH A CHECK -> “DELETE”.
2.2 -> “2ND LEVEL INTERFACE” -> SELECT EVERYTHING IN THE TABLE WITH A CHECK -> “DELETE”.
2.3 -> “ETH INTERFACE”, IF CREATED, DO NOT DELETE.
3. CREATE “WAN SERVICE” SETTINGS.
3.1 -> “WAN SERVICE” -> “ADD” -> “NEXT” -> “NEXT”.
3.2 CHECK THE CHECKS ON -> “REPEAT PPP IN AUTHENTICATION ERROR”, AND IF THERE IS THE SAME BELOW -> “ENABLE NAT”, AND -> “ENABLE FIREWALL”.
3.3 ENTER YOUR LOGIN AND PASSWORD -> “NEXT”, “PPP”-MOVE TO THE LEFT, “USB”-MOVE TO THE RIGHT, -> “NEXT”, “USB”-MOVE TO THE RIGHT, “PPP”-MOVE TO THE LEFT, -> “NEXT” , -> “APPLY AND SAVE”.
4. IN “WAN SERVICE” WE CREATE SETTINGS FOR “TV”.
4.1 -> “ADD” -> “NEXT”, SELECT THE BOTTOM ONE IN THE LINE -> “BRIGING” -> “APPLY AND SAVE”.
5. WE CREATE A GROUP FOR “TV”.
5.1 -> “GROUPING INTERFACES”, -> “ADD”, GROUP NAME “TV”, “BR_ETH/ETH0.2” MOVE TO THE LEFT, “ETH3/ETH3,ETH2” MOVE TO THE LEFT -> “APPLY AND SAVE”.
READY!!!

ATTENTION!!! After setting up the modem, it is recommended to change the standard login/password to the web interface.